Equipment

	__ __
Brand	Brand - __
Availability	Availability - __
Options	Options - __
Description	Description - __
SKU	SKU - __
	View product

LUMii

LUMii Digita 600W Electronic Ballast - electronic ballast / choke

350,00 lei

Large microscope 60x-100x magnification

66,00 lei

Maxibright Warpdrive 600W Power Pack - electronic ballast / choke

191,00 lei

Hortilight

HortiLight Ballast 600W - magnetic ballast / choke

153,00 lei

Mari 600W - magnetic ballast / choke

153,00 lei

LUMATEK

LUMATEK 600W 240V Controllable Electronic Ballast

492,00 lei

LUMATEK 600W 240V CONTROLLABLE BALLAST is a digital controllable ballast that can operate with both high-pressure sodium (HPS) and metal-halide (MH) lamps. It provides stable and precise voltage to the lamp, creating higher PAR/PPF output and is nevertheless far more energy efficient than most ballasts on the market! The ballast features intelligent start technology and a soft-dimming mechanism! It can be externally controlled with LUMATEK Control Panel Plus 2.0 (sold separately).

Output power: 600W
4 operating modes: 250W - 400W - 600W - 660W
generates very little heat compared with other ballasts on the market
operates silently
Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
5-year warranty!

An electronic ballast is a solution to the problem of irregular voltage in the power grid! Magnetic ballasts age over time, begin to make noise and consume more electricity, heat up more and more while their light output decreases. This does not happen with digital ballasts—they maintain the same level of output and efficiency. LUMATEK ballasts are programmed for “soft start”, meaning no voltage or current peak is required to start the lamp; this extends bulb life, does not overload the electrical installation and allows a larger number of ballasts to start safely at the same time.

Full technical specifications:

Output power: 600W
Input voltage: 240V, 50/60Hz
Maximum current: 2.7A
power factor*: > 0.99
Efficiency: 96%
THD*: < 8%
Dimming capability / 4 operating modes: 250W - 400W - 600W - 660W
Compatible with: 250W, 400W, 600W HPS / MH lamps
Operating frequency: high frequency
generates very little heat compared with other ballasts on the market
operates silently
Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
Dimensions: 310 x 114 x 81mm
Weight: 2.7kg
warranty: 5 years

Operating instructions:

For use with a 250W HPS or MH lamp: the ballast must be always and only in 250W mode!
For use with a 400W HPS or MH lamp: the ballast must never be in 600W or 660W mode!
For use with a 600W HPS or MH lamp: Start in 600W mode and only after the lamp has fully warmed up (after approximately 10min. of operation), can you switch to 660W mode!

Disconnect the power when changing the lamp!
LUMATEK recommends replacing the lamp after 6-12 months of operation!
VERY IMPORTANT: allow the lamp to cool completely (20-30min.) before switching it on again! (Doing otherwise shortens its life.)
Also, do not switch the lamp off before it has reached full power!

MST Hybrid Ballast 600W

202,00 lei

Silent Fan 300 mm 2700 m3/h - Sound-insulated turbine fan 320W (duct fan)

1.365,00 lei

LUMii

LUMii Cord Set with 4m Cord - lamp holder with 4 m cable

39,00 lei

LUMii

LUMii Digita 1000W Electronic Ballast - Electronic Ballast/Choke

655,00 lei

LUMATEK

LUMATEK 1000W 240V CONTROLLABLE digital ballast

655,00 lei

LUMATEK 1000W 240V CONTROLLABLE BALLAST is a digitally controllable ballast that can operate with both sodium (HPS) and metal-halide (MH) lamps. It provides stable, precise voltage to the lamp, delivering higher PAR/PPF output while being far more energy-efficient than most ballasts on the market. The ballast features intelligent start technology and a soft-dimming mechanism. It can be externally controlled with the LUMATEK Control Panel Plus 2.0 (sold separately).

output power: 1000W
4 operating modes: 600W - 750W - 1000W - 1000W SL
generates very little heat compared with other ballasts on the market
operates silently
Protection against short circuits, overheating, overvoltage / undervoltage and end of lamp life!
5-year warranty!

An electronic ballast is a solution to the problem of irregular mains voltage. Magnetic ballasts age over time, become noisy and consume more electricity, while heating up ever more as their light output declines. This does not happen with digital ballasts: they maintain the same output and efficiency. LUMATEK ballasts are programmed for a “soft start”, meaning no voltage or current spike is required to start the lamp. This extends bulb life, does not strain the electrical installation and enables more ballasts to be started safely at the same time.

Full technical specifications:

output power: 1000W
Input voltage: 240V, 50/60Hz
max. current: 4.7A
power factor*: > 0.99
THD*: < 10%
dimming capability / 4 operating modes: 600W - 750W - 1000W - 1000W SL
compatible with: 600W, 750W, 1000W HPS / MH lamps
operating frequency: high frequency
generates very little heat compared with other ballasts on the market
operates silently
Protection against short circuit, overheating, overvoltage / undervoltage, end of lamp life!
dimensions: 318 x 166 x 96mm
weight: 4.25 kg
warranty: 5 years

Operating instructions:

for use with a 600W HPS or MH lamp: the ballast must always be set to 600W mode only!
for use with a 750W HPS or MH lamp: the ballast must never be set to 1000W or 1000W SL mode!
for use with a 1000W HPS or MH lamp: start in 1000W mode and only after the lamp is fully warmed up (after around 10 min. of operation), you can switch to 1000W SL mode!

Disconnect the power when changing the lamp!
LUMATEK recommends replacing the lamp after 6-12 months of operation!
VERY IMPORTANT: allow the lamp to cool completely (20-30min.) before switching it on again! (Doing otherwise shortens its life.)
Also, do not switch the lamp off before it has reached full power!

Agrolite CL2 CMH 315W - magnetic ballast / choke

137,00 lei

DIMLUX

Dimlux temperature sensor

131,00 lei 271,00 lei

TechGrow

TechGrow Clima Control Basic Plus 14A Digital Controller for Temperature, Min/Max Speed and Hysteresis - 2 Fans

581,00 lei

DIMLUX

Dimlux Maxi Controller - Controller

972,00 lei 1.953,00 lei

Forget about a distribution board, timer box and relays! Dimlux lighting fixtures can be plugged directly into the socket! Simply set the on and off times and your lighting is ready to operate!

Dimlux Maxi Controller is a modular control system for Dimlux lighting, fans and heating. It can control up to 160 Dimlux lighting fixtures or ballasts. You can set the desired brightness using the + and - buttons. The Maxi Controller controls and monitors CO₂, plant temperature and vapour pressure deficit (VPD) depending on the selected connected sensors. Why choose the Dimlux Maxi Controller?

Gradual to continuously variable dimming.
Create optimal growing conditions for your crop.
Advanced connectivity and control options.
Simulates sunrise and sunset.
Datalog function (continuous recording of measured data)

Features:

the controller works with a 5m standard Interlink cable (included)
can control up to 160 Dimlux lighting fixtures or ballasts in groups of 40
the first group of 40 can be controlled with all sensors
switches lighting manually or automatically
simulates sunrise and sunset
measures ambient temperature via a temperature sensor
measures relative humidity via a RH sensor
measures plant temperature via a plant temperature camera
displays the vapour pressure deficit (VPD)
controls CO₂ via a CO₂ sensor
detects flammable, toxic and harmful gases via a Gas Protect CO₂
displays min./max. values for all sensors with a time stamp
Datalog function for recording measured data from all sensors
controls the fan based on temperature and humidity (with FAN/AUX BOX)
controls a humidifier or dehumidifier and heating (with AUX BOX or FAN/AUX BOX)

Instructions for use in English: here* and here*

OPTIMAL CONTROL, MAXIMUM EFFICIENCY. Maxi Controller is a modular system* for controlling Dimlux lighting, fans and heating. It also controls and monitors CO2, vapour pressure deficit (VPD) and installation temperature, depending on the selected sensors. Maxi Controller can control up to 160 Dimlux Expert luminaires or Xtreme ballasts. It can silently switch the lighting on or off using the built-in timer. The lighting can also be variably dimmed to reach the desired output. The controller can adjust output according to the room temperature. The Dimlux lighting system dims automatically once a set temperature is exceeded. If the temperature is still too high, Maxi Controller will switch off all or half of the luminaires until the desired temperature is reached. Dimlux Expert luminaires or Xtreme ballasts can be connected directly to a power outlet. Simply set the on/off times and the system is ready to operate. The desired light intensity can be set with the + and – buttons. The Maxi Controller can also operate with asynchronous timing, for example 10 hours on and 10 hours off. This setting reduces total cycles by almost 20%. Sunrise and sunset can also be simulated. Maxi Controller also has a thermostat/hygrostat function. It is also possible to regulate the CO₂ level in an enclosed room using an extremely accurate dual-beam CO₂ sensor. This CO₂ sensor can control CO₂ generators and cold CO₂ systems. *The controller can be expanded to include an AUX BOX, FAN/AUX BOX, CO₂ sensor, CO₂ Gas Protect sensor, plant-temperature camera, humidity sensor and temperature sensor (sold separately).
COMPREHENSIVE AND PRECISE SETTINGS. In addition to the extensive 7 dimming levels, the Dimlux Maxi Controller can adjust light output according to room temperature. It also facilitates the transition from gradual dimming to continuously variable dimming, making it even easier to achieve the perfect lighting setting. This is possible by pressing the + and – buttons (brightness), or by setting the desired temperature and leaving the rest to the Dimlux Maxi Controller. When the preset temperature is exceeded, the lights automatically dim or are even partially switched off.
SENSORS: MEASUREMENT = KNOWLEDGE. Several sensors are available that can be connected to the Dimlux Maxi Controller. Temperature sensor and humidity sensor can be combined with a plant-temperature sensor for optimal plant growth. The values obtained from the sensors are then analysed and combined to achieve the optimal relationship between temperature, humidity and plant temperature — and therefore vapour pressure deficit.
SUNRISE AND SUNSET SIMULATION. Plants do not use photosynthesis until a certain temperature is reached. When lighting switches on after a dark period, this can be stressful and may affect growth; condensation may also form and cause rot. The Dimlux Maxi Controller can prevent this by slowly switching the Dimlux Expert lighting systems on and off, thereby simulating sunrise and sunset.
DATALOG FUNCTION. The data-logging function makes it possible to store all measured values from the controller on a USB flash drive for later viewing in graphical form on your computer. The controller records all values to the flash drive every minute.

DIMLUX

Dimlux Aux Box - ventilation and climate box

382,00 lei 801,00 lei

DIMLUX

Dimlux Plant Temperature Camera

710,00 lei 1.284,00 lei

Plant temperature is more important than ambient temperature! When the camera is connected, the climate can be controlled based on plant temperature. If the plant temperature becomes too high, the Dimlux Maxi Controller will dim the lights to keep the stomata open. In the event of water shortage (e.g. due to a faulty pump), the lights are also dimmed or switched off to prevent crop damage.

infrared camera for heat detection
highly precise environmental control
allows the Dimlux Maxi Controller to calculate VPD*
used by the professional horticulture industry
very easy to install – plugs directly into the Dimlux Maxi Controller
10m cable

*Note: see the detailed description for an explanation of vapour pressure deficit (VPD).

See how to calculate your plant's VPD: here*

Dimlux Plant Temperature Camera is a fantastic accessory that accurately measures your plant's infrared levels and sends the information back to the Dimlux Maxi Controller. This information is then used together with room temperature and humidity readings to calculate and display the vapour pressure deficit (VPD)* – the potential of the surrounding air to draw moisture from the plant. It gives the grower the most accurate information on how much the plants need to transpire (release moisture through their leaves) to reach equilibrium with the surrounding atmosphere. A high vapour pressure deficit means your plants will lose more water through their stomata. Low vapour pressure deficits mean plants retain water more easily (great for cuttings, etc.). The Dimlux Maxi Controller can regulate your lighting power according to the temperature difference between the plants and the surrounding atmosphere, ensuring that VPD levels are always within the correct range.

VPD (VAPOUR PRESSURE DEFICIT) VAPOUR PRESSURE DEFICIT. The plant temperature camera, connected to and integrated with the Dimlux Maxi Controller, measures the plant temperature and displays the results on the Dimlux Maxi Controller.

The question is: Why do we need a plant temperature camera at all?
The reason is that it is crucial for the Dimlux Maxi Controller to understand the plant's overall condition or health. The temperature of a healthy plant should always be lower than the ambient temperature in which it lives. Water and nutrients continuously move through the plant, keeping it cooler than its surroundings. If the plant temperature rises to the same temperature as the ambient air, it is no longer healthy and will begin to wilt and eventually die. Factors that contribute to this undesirable condition or environment include:

High-intensity discharge lighting - HPS (sodium) or MH (metal-halide) lamps
Lack of adequate extraction or ventilation
Incorrect water supply to the plant.

With the help and intelligence of the Dimlux Maxi Controller, the lights it controls are dimmed until the plant temperature falls below the ambient temperature and remain that way until the fault causing the temperature imbalance between the plant and the ambient air is resolved (for example, a plumbing or electrical fault).
Now, with the plant temperature camera, the temperature sensor and the Dimlux humidity sensor, connected to and integrated with the Dimlux Maxi Controller, the controller is programmed to analyse the ambient temperature, plant temperature and humidity levels, and to calculate another vitally important measurement, described as “Vapour Pressure Deficit” or VPD. This measurement is an indicator that best describes the level of environmental support in which the plant lives.
This environment is critical for optimal growth and nutrient uptake, and depends on how hot and humid it is. If the indoor environment is lit with HPS, MH or CDM lighting, and humidity is above 70 to 80% while temperatures are above 35°C, then the plants' ability to photosynthesise and to take up CO₂ and to absorb nutrients decreases; consequently, the plants' ability to grow and produce flowers and fruit also decreases.
Therefore, if the environment cannot be controlled or restored to normal conditions, your plants' ability to absorb nutrients and grow optimally will also be reduced. Consequently, reducing the light output and heat from HPS, MH or CDM lighting is the next logical step in balancing the parameters [heat and humidity] to maintain high photosynthetic activity and, more importantly, to keep the stomata in the leaves open.
By keeping the stomata open for gas exchange, which is the main force driving water and nutrients through the plant, more sugars and amino acids are formed in the flowers/fruits for optimal production. This level of control is possible only with the Dimlux Maxi Controller and your Dimlux lighting. For greater flexibility in your indoor environment in relation to your lighting, the right control equipment is the key to consistently maximising the quality and yield potential of your plants and every harvest!
The idea of VPD and its application is new, exciting and perhaps confusing to some. The idea, once again, is that if it is too hot or too humid for your plants to function optimally, why waste electricity on lights at full power when the plants cannot use the light, when we can balance heat and humidity by reducing lighting power and bringing the VPD reading to around 1 to 1.2?
By doing this, the plants will use the nutrients you feed them, and therefore grow and produce optimally. Again, this is possible only with Dimlux lighting, Dimlux Maxi Controller and the plant temperature camera, the temperature sensor and the Dimlux humidity sensor. The same yields have been achieved even at 70% light output, simply because the other parameters were balanced and optimal VPD was achieved.

TechGrow

TechGrow Clima Eco 5A (Minimum speed) - minimum speed controller (1 fan)

277,00 lei

Bluelab

Bluelab PeriPod M3 Peristaltic Dosing Pump for pH Controller (120 ml/min)

3.002,00 lei

Hager Power Panel 36x600W - distribution panel (box) with timer, 36 sockets + 2 for heating, with 8 circuits

2.178,00 lei

Electrostart

Electrostart 1000W - Magnetic Ballast

391,00 lei

Bevoghtiger HE 402 Flens Rond 200mm Cap 10LTR

Humidifier HE 402 Flange Round 200mm Cap 10LTR

2.723,00 lei

Faran analogue hygrostat – humidity controller

355,00 lei

Faran Analogue Hygrostat is a reliable analogue controller for automatic humidity management in grow rooms, greenhouses, nurseries and other climate-controlled spaces. The device monitors relative air humidity and automatically switches a humidifier on or off to maintain the set level, without complex settings or an internet connection.

Faran Analogue Hygrostat is a practical solution for automatically maintaining optimum humidity in plant-growing spaces. Instead of constantly monitoring and switching on the humidifier manually, the device controls relative humidity and manages the connected humidifier according to the preset value.

Thanks to the analogue control, setup is quick and intuitive. No apps, Wi-Fi connection or digital programming are needed – simply set the desired humidity level with the rotary potentiometer and the hygrostat automatically takes care of the rest.

The device is designed to work with humidifiers such as Faran HR15, Faran HR50 and other standard humidifiers controlled by switching the power supply on and off. When the set humidity is reached, the hygrostat cuts power to the humidifier; when it drops below the set value, it switches it on again.

For best results, the manufacturer recommends installation at plant canopy height and away from the humidifier's direct airflow, to avoid inaccurate readings.

Technical specifications

✔️ Manufacturer: Faran

✔️ Type: Analogue hygrostat

✔️ Function: Automatic humidity control

✔️ Operating range: 10% – 80% RH

✔️ Control method: ON/OFF

✔️ Accuracy: ±5% RH

✔️ Hysteresis: approximately 3% RH

✔️ Sensor: Nylon Loop

✔️ Power supply: 220 V AC / 50 Hz

✔️ Maximum switching current: 2.2 A

✔️ Power-cable length: 2 m

✔️ Dimensions: 140 × 95 × 45 mm

✔️ Operating temperature: 10°C – 40°C.

📦 The kit includes

✔️ 1 × Faran Analogue Hygrostat

✔️ Power cable

✔️ User manual.

📋 Instructions for use

Mount the hygrostat on a wall at plant level.
Avoid mounting directly next to the humidifier or in the direct path of the water mist.
Connect the humidifier to the hygrostat.
Set the desired relative humidity using the rotary control.
Leave the system running for several hours and check the humidity with a thermo-hygrometer.
If necessary, fine-tune the setting until the desired level is reached.

⚠️ Important: For the most accurate readings, place the hygrostat away from the humidifier’s direct airflow, heaters and ventilation openings. This gives a true humidity reading in the plant zone and more precise climate control.

G-systems

G-Systems Timer Box 8x600W + Heating - 8-Socket Lamp Timer Box + 1 Heater Socket, 2 Circuits

573,00 lei

TechGrow

TechGrow Day/Night Fan Controller 7A - 2 Fans

573,00 lei

Hager Power Panel 32x600W - distribution panel (box) with timer, 32 sockets + 2 for heating, 8 circuits

1.910,00 lei

VEAB CWK 315-3-2.5 water duct cooler for round duct – Ø315 mm 1410m3 1260L/PU 8.3KW

4.093,00 lei

VEAB CWK 315-3-2.5 is a professional duct water cooler for Ø315 mm air ducts, designed to cool air in ventilation and air-conditioning systems using cold water. The heat exchanger has copper tubes and aluminium fins, while the built-in stainless-steel tray collects the resulting condensate. This model is suitable for both central ventilation systems and cooling individual rooms or greenhouses.

CWK 315-3-2.5 is installed directly in a round air duct and uses chilled water as the energy carrier. This allows the air passing through the ventilation system to be cooled without the need for a direct evaporative refrigerant heat exchanger.

The construction is designed for easy maintenance – the casing has an opening cover for inspection and cleaning, while condensate is drained via a stainless-steel tray and G½" drain connection.

Technical specifications

Manufacturer: VEAB
Model: CWK 315-3-2.5
Type: Duct water cooler
Purpose: Ventilation-air cooling
Heat-transfer medium: Cold / chilled water
Air-duct diameter: Ø315 mm
Number of heat exchanger rows: 3
Fin spacing: 2.5 mm
Pipe connections: Ø22 mm
Condensate drain: G½"
Internal heat exchanger volume: 1.61 l
Maximum working pressure: 1.0 MPa / 10 bar
Installation: In a horizontal air duct
Heat exchanger: Copper pipes with aluminium fins
Condensate tray: Stainless steel
Air-duct connections: With rubber seals.

📐 Dimensions

According to the current VEAB technical documentation for CWK 315-3-2.5:

💨 Cooling capacity

Cooling capacity is not a fixed value. It depends on airflow and air temperature, humidity, as well as the temperature and flow rate of the chilled water.

For example, with water at 6/12°C, the VEAB table gives the following indicative results for CWK 315-3-2.5:

Airflow	Inlet air	RH	Outlet air	Power
900 m³/h	25°C	50%	15.2°C	3.4 kW
900 m³/h	30°C	45%	16.3°C	5.8 kW
1590 m³/h	25°C	50%	16.8°C	4.8 kW
1590 m³/h	30°C	45%	17.8°C	9.3 kW
2280 m³/h	25°C	50%	17.6°C	6.1 kW
2280 m³/h	30°C	45%	18.6°C	12.8 kW

These values are example design points, not a constant product output. For a specific system, VEAB recommends calculation according to the actual air and water parameters.

💧 Control and automation

The CWK itself is a water-to-air heat exchanger. For automatic temperature control, the system can be supplemented with:

temperature controller → sensor → control valve → actuator → frost protection.

For example, VEAB specifies for the CWK 315-3-2.5 a two-way valve ZTV15-1.6 (Kvs 1.6) as a suitable option in its selection table.

This is important for the product page – control components must not be presented as included as standard, unless the specific offer explicitly states this.

💦 Condensate drainage

When warm, humid air is cooled, the heat exchanger temperature may fall below the dew point and condensation may form.

For this reason, the CWK is equipped with a stainless-steel tray that collects the water and allows it to drain through a G½" drain connection.

🛠️ Construction and maintenance

The heat exchanger uses copper tubes and aluminium fins, while the casing is made of protected sheet metal. The opening cover provides access to the interior for periodic cleaning and inspection.

Rubber seals on the round connections make integration into the ventilation system easier.

You can view the manual

by clicking on the label.

🏭 Suitable for

VEAB CWK 315-3-2.5 is suitable for:

ventilation and air-conditioning systems;
cooling of supply fresh air;
air-conditioning of individual rooms and zones;
greenhouses and controlled environments;
production and technical premises;
systems with a chiller or another source of cold water.

The manufacturer explicitly states use both for cooling ventilation air and for individual cooling of specific rooms or zones.

📦 Product information

Model: CWK 315-3-2.5
Manufacturer: VEAB Heat Tech AB
Diameter: Ø315 mm
Warranty: 24 months

⭐ Key benefits

✔️ Professional water cooler for Ø315 mm air ducts
✔️ Operates with cold water
✔️ 3-row heat exchanger
✔️ Copper tubes and aluminium fins
✔️ Integrated stainless-steel condensate tray
✔️ Drain connection G½"
✔️ Maximum working pressure 10 bar
✔️ Openable housing for easy cleaning
✔️ Option for automatic temperature control
✔️ Manufactured by VEAB.