Humidifiers

Cornwall 6L Humidifier is made from recyclable plastic. It can operate continuously for 16 hours. Through ultrasonic-wave vibration, the humidifier breaks water droplets into particles from 1 to 5 μm. The particles are then diffused by a fan. During this process, a large number of anions are produced and dispersed. This allows the unit to humidify and cool the air. Its main features are as follows:

 

• produces a soft, refreshing mist
• energy-saving
• quiet
• automatic shut-off
• long service life

 

• Voltage: 220-240 V; ~ 50Hz
• Power: 25W
• Water tank: 6L
• Maximum: 350ml/h

Mist Maker 3 air humidifier - 1200ml/h provides the required humidity for your plants without emitting heat.

• Creates mist from fine water droplets through ultrasonic vibrations
• Does not raise the room temperature
• Uses 1200ml of water per hour
• Power: 68W
• Up to 2000 operating hours (the ceramic discs can be replaced)
• The set includes a humidifier with 3 ceramic discs and an adapter with a 10m power cable.
• Sold WITHOUT the float. You can purchase it here

 

The high-quality Mist Maker 3 humidifier is very compact and can be easily installed in rooms of different sizes.

Can be used:

• For growing plants outdoors and indoors
• In aquariums
• Fountains

Its design allows easy cleaning of the ceramic discs from accumulated limescale or other impurities from the water.

It can be combined with a float, allowing it to be installed in different water reservoirs.

It is equipped with a water-level sensor that switches off the humidifier when the level becomes too low.

Float for Mist Maker 3

Used to position and keep the humidifier at the optimal depth in water reservoirs.

Material: plastic

Enhance your surroundings with the Humidifier Cornwall 8.5L – the perfect helper for maintaining optimal humidity at home or in the office.

Capacity: 8.5 litres, ensuring long-lasting operation without frequent refilling. Technology: Modern ultrasonic technology for even and quiet water-mist dispersion. Adjustment: Adjustable humidification intensity to suit your needs. Design: An elegant, compact design that fits easily into any interior. Benefits: Maintains healthy, comfortable room humidity, helping prevent dry skin and respiratory discomfort. Quiet operation, ideal for bedrooms and workspaces. Easy to use and maintain. An eco-friendly solution for improving air quality. With Humidifier Cornwall 8.5L, you will notice the difference in comfort and quality of life. Ideal for seasons when heating or air conditioning is running at full power.

Mist Maker 5 air humidifier – 1600ml/h provides the necessary humidity for your plants without emitting heat.

• Creates mist from fine water droplets through ultrasonic vibrations
• Does not raise the room temperature
• Uses 1600ml of water per hour
• Power: 100W
• Up to 2000 hours of operation (the ceramic discs are replaceable)
• The set includes a humidifier with 5 ceramic discs and an adapter with a 10m power cable.
• Sold WITHOUT the float. It can be purchased here

 

The high-quality Mist Maker 5 humidifier is very compact and can easily be installed in rooms of different sizes.

Can be used:

• For growing plants outdoors and indoors
• In aquariums
• Fountains

Its design allows easy cleaning of the ceramic discs from accumulated limescale or other contaminants from the water.

It can be combined with a float, allowing it to be installed in different water reservoirs.

It is equipped with a water-level sensor that switches off the humidifier when the level becomes too low.

Replacement ceramic discs for Mist Maker 5

• 5 pieces per pack

Float for Mist Maker 5

Used to position and keep the humidifier at the optimal depth in water reservoirs.

Material: plastic

The Monzon humidifier from Neptune Hydroponics is fitted with an automatic mechanism that maintains a sufficient water level via a water inlet, which can be connected to a reservoir or running water. In addition to its autonomy, this model has an unusually high output capacity of 5l/h.

 

• voltage: 220-240V
• power: 300W
• maximum evaporator capacity: 5l/h
• airflow: ≥ 120m3/h
• spray outlet diameter: φ 110mm
• water particles: ≥ 10µm
• inlet tube opening size: 13mm
• dimensions: 47 x 24 x 33cm (without the evaporator tube)

🔹 This water filter is designed for use with RAM wall-mounted humidifiers. It effectively removes mineral deposits and other contaminants from the water, providing cleaner water and extending the life of your humidifier. It is especially recommended for areas with hard water.

🔹 Detailed specifications:

• Manufacturer: RAM
• Type: Inline DI (deionization) filter
• Compatibility: RAM Wall Humidifier
• Function: Removes mineral deposits and contaminants from the water
• Wear indicator: A color change from blue to gold indicates that the resin needs to be replaced
• Dimensions: Standard for connection to wall-mounted humidifiers
• Installation: Easy to install and maintain

 

🔹 Recommendations and instructions for use:

1. Disconnect the humidifier from the power supply and water supply.
2. Remove the old filter, if present.
3. Install the new RAM Inline DI Resin Water Filter, ensuring that it is properly positioned and secured.
4. Reconnect the humidifier to the water supply and power supply.
5. Regularly check and maintain the filter to ensure optimal humidifier performance.

 

✅ Benefits of use:

• Improved water quality: Removes contaminants from the water, providing cleaner water for the appliance.
• Extended humidifier life: Prevents the buildup of mineral deposits that can damage the device.
• Easy maintenance: Quick and easy filter installation and replacement.
• Cost-effectiveness: Regular filter replacement can reduce the need for expensive humidifier repairs.

The Mist Maker 12 air humidifier - 5300ml/h provides the necessary humidity for your plants without emitting heat.

• Creates mist from fine water droplets through ultrasonic vibrations
• Does not raise the room temperature
• Uses 5300ml of water per hour
• Power: 300W
• Up to 2000 hours of operation (the ceramic discs are replaceable)
• The set includes: humidifier with 12 ceramic discs, a power adapter with 10m cable, float and 12 spare ceramic discs

The high-quality Mist Maker 12 humidifier is very compact and can easily be installed in rooms of different sizes.

Can be used:

• For growing plants outdoors and indoors
• In aquariums
• Fountains

Its design allows easy cleaning of the ceramic discs from accumulated limescale or other contaminants from the water.

It can be combined with a float, allowing it to be fitted in various water reservoirs.

It is equipped with a water-level sensor that switches off the humidifier when the level becomes too low.

Bevoghtiger HE 402 Flens Rond 200mm Cap 10LTR is an excellent choice for anyone seeking a high-performance yet compact and convenient ventilation and air-conditioning system. With a 200 mm flange diameter, this device can be easily integrated into any airflow system, giving you the flexibility to use it in the way that best meets your needs. This device stands out with a 10-litre capacity, meaning it can manage large volumes of air efficiently and reliably. Thanks to its high performance, it can improve air quality in large spaces or maintain stable temperature and humidity in your home, office or production facility.

Faran Analogue Hygrostat is a reliable analogue controller for automatic humidity management in grow rooms, greenhouses, nurseries and other climate-controlled spaces. The device monitors relative air humidity and automatically switches a humidifier on or off to maintain the set level, without complex settings or an internet connection.

Faran Analogue Hygrostat is a practical solution for automatically maintaining optimum humidity in plant-growing spaces. Instead of constantly monitoring and switching on the humidifier manually, the device controls relative humidity and manages the connected humidifier according to the preset value.

Thanks to the analogue control, setup is quick and intuitive. No apps, Wi-Fi connection or digital programming are needed – simply set the desired humidity level with the rotary potentiometer and the hygrostat automatically takes care of the rest.

The device is designed to work with humidifiers such as Faran HR15, Faran HR50 and other standard humidifiers controlled by switching the power supply on and off. When the set humidity is reached, the hygrostat cuts power to the humidifier; when it drops below the set value, it switches it on again.

For best results, the manufacturer recommends installation at plant canopy height and away from the humidifier's direct airflow, to avoid inaccurate readings.

 

Technical specifications

✔️ Manufacturer: Faran

✔️ Type: Analogue hygrostat

✔️ Function: Automatic humidity control

✔️ Operating range: 10% – 80% RH

✔️ Control method: ON/OFF

✔️ Accuracy: ±5% RH

✔️ Hysteresis: approximately 3% RH

✔️ Sensor: Nylon Loop

✔️ Power supply: 220 V AC / 50 Hz

✔️ Maximum switching current: 2.2 A

✔️ Power-cable length: 2 m

✔️ Dimensions: 140 × 95 × 45 mm

✔️ Operating temperature: 10°C – 40°C.

 

📦 The kit includes

✔️ 1 × Faran Analogue Hygrostat

✔️ Power cable

✔️ User manual.

 

📋 Instructions for use

1. Mount the hygrostat on a wall at plant level.
2. Avoid mounting directly next to the humidifier or in the direct path of the water mist.
3. Connect the humidifier to the hygrostat.
4. Set the desired relative humidity using the rotary control.
5. Leave the system running for several hours and check the humidity with a thermo-hygrometer.
6. If necessary, fine-tune the setting until the desired level is reached.

⚠️ Important: For the most accurate readings, place the hygrostat away from the humidifier’s direct airflow, heaters and ventilation openings. This gives a true humidity reading in the plant zone and more precise climate control.

 

 

VEAB CWK 315-3-2.5 is a professional duct water cooler for Ø315 mm air ducts, designed to cool air in ventilation and air-conditioning systems using cold water. The heat exchanger has copper tubes and aluminium fins, while the built-in stainless-steel tray collects the resulting condensate. This model is suitable for both central ventilation systems and cooling individual rooms or greenhouses.

CWK 315-3-2.5 is installed directly in a round air duct and uses chilled water as the energy carrier. This allows the air passing through the ventilation system to be cooled without the need for a direct evaporative refrigerant heat exchanger.

The construction is designed for easy maintenance – the casing has an opening cover for inspection and cleaning, while condensate is drained via a stainless-steel tray and G½" drain connection.

Technical specifications

• Manufacturer: VEAB
• Model: CWK 315-3-2.5
• Type: Duct water cooler
• Purpose: Ventilation-air cooling
• Heat-transfer medium: Cold / chilled water
• Air-duct diameter: Ø315 mm
• Number of heat exchanger rows: 3
• Fin spacing: 2.5 mm
• Pipe connections: Ø22 mm
• Condensate drain: G½"
• Internal heat exchanger volume: 1.61 l
• Maximum working pressure: 1.0 MPa / 10 bar
• Installation: In a horizontal air duct
• Heat exchanger: Copper pipes with aluminium fins
• Condensate tray: Stainless steel
• Air-duct connections: With rubber seals.

📐 Dimensions

According to the current VEAB technical documentation for CWK 315-3-2.5:

 

💨 Cooling capacity

Cooling capacity is not a fixed value. It depends on airflow and air temperature, humidity, as well as the temperature and flow rate of the chilled water.

For example, with water at 6/12°C, the VEAB table gives the following indicative results for CWK 315-3-2.5:

Airflow	Inlet air	RH	Outlet air	Power
900 m³/h	25°C	50%	15.2°C	3.4 kW
900 m³/h	30°C	45%	16.3°C	5.8 kW
1590 m³/h	25°C	50%	16.8°C	4.8 kW
1590 m³/h	30°C	45%	17.8°C	9.3 kW
2280 m³/h	25°C	50%	17.6°C	6.1 kW
2280 m³/h	30°C	45%	18.6°C	12.8 kW

These values are example design points, not a constant product output. For a specific system, VEAB recommends calculation according to the actual air and water parameters.

💧 Control and automation

The CWK itself is a water-to-air heat exchanger. For automatic temperature control, the system can be supplemented with:

temperature controller → sensor → control valve → actuator → frost protection.

For example, VEAB specifies for the CWK 315-3-2.5 a two-way valve ZTV15-1.6 (Kvs 1.6) as a suitable option in its selection table.

This is important for the product page – control components must not be presented as included as standard, unless the specific offer explicitly states this.

💦 Condensate drainage

When warm, humid air is cooled, the heat exchanger temperature may fall below the dew point and condensation may form.

For this reason, the CWK is equipped with a stainless-steel tray that collects the water and allows it to drain through a G½" drain connection.

🛠️ Construction and maintenance

The heat exchanger uses copper tubes and aluminium fins, while the casing is made of protected sheet metal. The opening cover provides access to the interior for periodic cleaning and inspection.

Rubber seals on the round connections make integration into the ventilation system easier.

You can view the manual

by clicking on the label.

🏭 Suitable for

VEAB CWK 315-3-2.5 is suitable for:

• ventilation and air-conditioning systems;
• cooling of supply fresh air;
• air-conditioning of individual rooms and zones;
• greenhouses and controlled environments;
• production and technical premises;
• systems with a chiller or another source of cold water.

The manufacturer explicitly states use both for cooling ventilation air and for individual cooling of specific rooms or zones.

📦 Product information

Model: CWK 315-3-2.5
Manufacturer: VEAB Heat Tech AB
Diameter: Ø315 mm
Warranty: 24 months

⭐ Key benefits

✔️ Professional water cooler for Ø315 mm air ducts
✔️ Operates with cold water
✔️ 3-row heat exchanger
✔️ Copper tubes and aluminium fins
✔️ Integrated stainless-steel condensate tray
✔️ Drain connection G½"
✔️ Maximum working pressure 10 bar
✔️ Openable housing for easy cleaning
✔️ Option for automatic temperature control
✔️ Manufactured by VEAB.

 

 

Industrial humidifier suitable for continuous use over many years. It creates a fine mist and ventilates it around the area. Easy to install and maintain. Suitable for greenhouses, nurseries, mushroom farms, farms, warehouses and more.

​

• Voltage: 220V 50Hz
• Power: 90W
• Capacity: 3-5 L/h
• Dimensions: 389x389x455 mm
• Weight: 7.7 kg
• Certificates: ISO, CE

 

Compact ultrasonic humidifier Mist Maker 9, which creates a fine mist without heat or chemicals — ideal for humidity control in rooms, greenhouses, aquariums and air-conditioning systems.

Detailed features

• Housing diameter 12 cm, height 3,3 cm.
• Power: 250 W.
• Cable length: 7,5 m.
• Steam/mist output: 675 ml/hour.
• Water consumption: 2700 ml/hour.
• Operating temperature range: from 5 °C to 40 °C.
• Number of generator sockets: 9.
• Designed for use in small spaces requiring high humidity; the housing has a special coating for easy cleaning.
• Weight: 5,400 kg.
• Warranty: 1 year.

 

Recommendations for use

• Install the transformer on a stable, level surface, away from direct contact with water and humid environments wherever possible.
• Ensure that the device is connected to a suitable power source and that the cable is securely fitted.
• Use in an area where relative humidity control is required – for example, in greenhouses, aquariums, grow rooms and more.
• Periodically check and drain the reservoir to prevent sediment buildup.
• Do not allow solid particles or fragments to enter the generator sockets – this may impair efficiency.
• After use or before storage, switch off the unit, clean it and store it in a dry place to extend its service life.

 

Benefits

Mist Maker 9 is a powerful ultrasonic humidifier that delivers a substantial volume of mist through 9 generators, with 250 W power and water consumption of up to 2700 ml/hour. With compact dimensions and a wide temperature range (5–40 °C), it is suitable for professional systems and home humidity-control solutions alike.

 

HE402 is a professional air humidifier for installation in ventilation systems, designed to maintain optimal humidity in plant-growing rooms, greenhouses and other climate-controlled spaces. With the correct water pressure, it provides a capacity of up to 10 litres per hour and is suitable for systems with an airflow of 600–700 m³. It operates without fine mist in the room, humidifying the air efficiently through evaporation.

HE402 is designed for professional applications where precise humidity control is required. It is installed in an air duct with a diameter of Ø200 mm and operates together with a suitable inline fan. For maximum performance, the manufacturer recommends inlet water pressure of at least 2 bar and an incoming air temperature of around 28–30°C. Under these conditions, the system achieves optimal humidification capacity.

The humidifier uses a special evaporative element through which the airflow passes. This allows even humidification without forming free water mist in the room, which is particularly suitable for environments with lighting, electronics and sensitive equipment.

If higher capacity is required, the system can be combined with a booster pump, which raises water pressure to 8 bar. This atomises the water into significantly finer droplets, improving evaporation and increasing humidification efficiency.

For automatic operation, the manufacturer recommends using a humidistat, which simultaneously controls the solenoid water valve, the fan and any booster pump. This way, the humidifier operates only when needed and a stable relative-humidity level is maintained.

Installing an air-distribution sleeve after the humidifier helps distribute humid air more evenly in the room, while using a filter before the fan limits dust accumulation on the evaporative element. An additional benefit of the system is that it also has a slight cooling effect on the air during operation.

 

Technical specifications

✔️ Type: Duct air humidifier

✔️ Model: HE402

✔️ Installation diameter: Ø200 mm

✔️ Humidification capacity: up to 10 L/hour

✔️ Recommended airflow: 600–700 m³

✔️ Minimum water pressure: 2 bar

✔️ Optimal incoming air temperature: 28–30°C

✔️ Can be used with a booster pump (up to 8 bar)

✔️ Compatible with Ruck RKS 200L inline fan

✔️ Suitable for automatic control via a humidistat.

 

📦 The kit includes

✔️ 1 × Air humidifier HE402

Note: The fan, humidistat, booster pump and air-distribution sleeve are sold separately unless included in a specific configuration.

 

Benefits

✔️ Capacity of up to 10 litres of humidification per hour

✔️ Suitable for rooms with a volume of 600–700 m³

✔️ Operates without direct water-mist spraying

✔️ Can be automatically controlled via a humidistat

✔️ Output can be increased with a booster pump

✔️ Helps cool the air during operation

✔️ Easy integration with existing ventilation systems

✔️ Suitable for continuous professional use.

 

Application

Suitable for:

• Greenhouses

• Seedling production areas

• Ventilation systems

• Climate-controlled rooms

• Storage areas

• Production areas

• Other spaces where optimal air humidity must be maintained.

 

📋 Instructions for use

1. Install the humidifier in Ø200 mm ducting.
2. Connect the unit to a water supply with a minimum pressure of 2 bar.
3. If necessary, install a booster pump for higher output.
4. Connect the fan and solenoid valve to a humidistat for automatic control.
5. Where possible, use an air-distribution sleeve for more even humidity distribution.
6. Periodically clean the evaporative element and keep the system free of dust build-up for optimal performance.

⚠️ Important: For correct operation, the manufacturer recommends that all electrical components (fan, solenoid valve and booster pump, if fitted) are switched on and off simultaneously via a humidistat. If the fan remains on after the water supply is stopped, humidification will continue for a while due to residual moisture in the evaporative element

FARAN HR-15 is a reliable industrial humidifier for medium-sized spaces measuring 15-30 m². It creates a fine mist and circulates it around the area.

 

• for nurseries, greenhouses, mushroom farms, animal breeding facilities, warehouses and more.
• Easy to install (connects directly to the tap or a water tank).
• Can be wall-mounted.
• Convenient handle for easy carrying.
• Made from high-quality, durable materials.

 

• humidification coverage: spaces up to 15-30 m²
• power consumption: 90W
• humidification capacity: 1500 ml / h

Features:

 

• Suitable for: nurseries, greenhouses, mushroom farms, animal breeding facilities, warehouses and more.
• Easy to install (connects directly to the tap or a water tank).
• Can be wall-mounted.
• Convenient handle for easy carrying.
• Long-lasting, made from high-quality materials.
• Suitable for chemical disinfection and deodorisation.

 

Technical specifications:

 

• humidification coverage: spaces up to 15-30 m²
• power supply: 110/220V, 50/60Hz
• power consumption: 90W
• humidification capacity: 1500 ml / h
• dimensions: 310 x 310 x 470 mm

 

Note:

1. Place it horizontally to control the water level!
2. Make sure the connecting cable is long enough!
3. Check and clean the water tank regularly!
4. If there is no humidification, disconnect the power supply and check the water level!
5. If the water overflows, close the water tap and check the float valve!

Industrial humidifier suitable for continuous use for years. It creates a fine mist and ventilates it around the area. Easy to install and maintain. Suitable for greenhouses, nurseries, mushroom farms, farms, warehouses, etc.

 

• Power supply: 220V 50Hz
• Power: 90W
• Capacity: 2.5l/h
• Dimensions: 330x330x350mm
• Certificates: ISO, CE