Hydroponic and Irrigation Systems

Autopot 47 L reservoir with included lid and rubber seal.

• capacity: 47 L
• colour: black
• dimensions H/W/D: 615 x 375 x 300 mm
• material: hard plastic

Note: Always raise your reservoir to a minimum of 150 mm above the highest AQUAvalve!

GrowMax GARDEN GROW 480 L/h, a high-capacity two-stage water filtration system, is designed for larger indoor or outdoor gardens.

• Eliminates 99% of chlorine and 90% of sediment down to 5 microns, instantly!
• Faster-growing and healthier plants, flowers and vegetables.
• Strengthens plant roots.
• Great for organic production!
• Protects beneficial microorganisms in your soil.
• Get 100% efficiency from your nutrients and fertilizers.

Full product information here!

This system is designed as a standalone filter for the immediate removal of chlorine and sediment from water. It is rated to remove up to 99% of chlorine and can clean up to 90% of sediment above 5 microns. Having chlorine- and sediment-free water is essential for growing healthy plants and maintaining beneficial microorganisms, bacteria and fungi in the root zone and growing media. These microbes cannot survive in the presence of chlorine. Chlorine-free water is also essential for organic fruit and vegetables, hydroponics and every method of organic gardening in general. This filter is not designed to reduce the parts per million (PPM) of your water. Most of these PPM particles are minerals, which can only be removed by reverse osmosis systems.

REMOVES: chlorine, sediment, dirt, rust, oxidising herbicides and pesticides, volatile organic contaminants (chemical contaminants, benzenes, toluene, oils, trihalomethanes, detergents, polychlorinated biphenyls)

When to replace the filters:

• sediment filter – approximately every 16000 litres of treated water or if it is clogged
• carbon filter – approximately every 25000 litres of treated water or according to its use (see the example below*)

*Example use:

• 1 hour per week (1920 L/month) – replace the filter 1 time per year
• 1 hour per day, 4 days per week (7680 L/month) – replace the filter 1 time every 3 months
• 1 hour per day, every day (14400 L/month) – replace the filter 1 time every 7 weeks
• 30 minutes per day, every day (7200 L/month) – replace the filter 1 time every 3.5 months

*Replacement time is relative, as it depends on the hardness of the water you use.

Warranty:

• The product has a 1-year warranty.
• When you register your product here, you will automatically receive one more year of warranty for your product, for a total of 2 YEARS PRODUCT WARRANTY.

Compact and efficient reverse-osmosis system with a pump, delivering up to 400 litres of clean water per day. An excellent choice for small gardens, hydroponics, aquariums and households, ensuring removal of up to 99 % of contaminants – including salts, heavy metals, chlorine, pesticides and more.

Detailed features

• Capacity: 400 L/day
• Application: Suitable for small gardens, home aquariums and household use
• Removes: Up to 99 % of residues such as salts, heavy metals, chlorine, insecticides, pesticides and herbicides
• Pressure pump: Ensures a stable, efficient flow of purified water required by hydroponic systems and gardens
• Compact design: Suitable for limited spaces and easy to install.

Recommendations for use

• Before first use, it is recommended to clean it as described in the manual (available to download on the website)
• For optimal operation, replace the filters according to the manufacturer’s instructions.
• Monitor the water flow to avoid overload at low pressure when no pump is used.
• Monitor water quality, especially where source water varies (for example, very hard water or high mineralisation).

Summary – Benefits

• High efficiency: 400 l of clean water per day – perfect capacity for small to medium needs.
• Reliable contaminant removal: up to 99 % removal of various types of pollutants and contaminants.
• Convenience and compactness: With a pump for stable flow and a small size – easy to install anywhere.
• Versatility: Suitable for the home, hobby gardening, hydroponics and aquariums.

Compact and efficient Hailea HX-800 submersible pump with adjustable flow rate up to 285 l/h and maximum head of about 0,5 m – suitable for aquariums, hydroponics and small circulation systems.

Detailed features

• Flow rate: 285 l/h.
• Power: 3 W.
• Maximum head: 0,5 m.
• Power supply: 220-240 V / 50-60 Hz.
• Outlet diameter: 9 mm.
• Dimensions: 55 × 65 × 80 mm.
• Weight: approximately 0,22 kg.

Design and features:

• Housing made of ABS plastic, resistant to corrosion and aggressive
• Shaft: stainless steel, suitable for fresh and salt water.
• Built-in adjustable flow controller
• Rubber suction feet for installation – to secure it to surfaces
• Ability to operate at low water level

Recommendations for use

• Secure the pump to a smooth surface using the rubber suction feet to minimise vibration.
• Use a hose or pipe matching the outlet diameter (e.g. 9 mm), or an adapter.
• Adjust the flow rate as needed using the built-in controller.
• Clean the intake cover / filter regularly to prevent clogging and reduced flow.
• Never allow the pump to run dry – make sure it is always in contact with water.
• When using nutrient solutions or aggressive liquids, check material compatibility (ABS, shaft, seals).

Benefits

Hailea HX-800 offers a good balance between size and performance – despite its compact dimensions, it delivers 285 l/h and can be adjusted to suit the system's needs. Its low power consumption makes operation economical, while its construction is reliable and resistant to different water environments.

Maintaining a constant nutrient-solution temperature in hydroponic systems (NFT and DWC) within optimum limits is extremely important for preserving oxygen levels and protecting roots from Pythium* and other diseases.

With the Hailea HC-130A 200 - 1000 L/h chiller, controlling the water temperature in your hydroponic system or aquarium is easier than ever!

• compatible with fresh and salt water
• environmentally friendly refrigerant R134a
• low noise levels
• easy-to-use digital controller
• function for automatic shutdown against overheating
• for tank / aquarium volume: 130 L

The chiller is designed to operate with a water pump with a flow rate of 1000L/h (sold separately).

Instructional video: here.*

Features:

• model: HC-130A
• recommended flow rate: 200 - 1000 L/h
• for tank / aquarium volume: 130 L
• fittings: ⌀ 12 or ⌀ 17 mm (included)
• power: 1/15 HP 
• power consumption: 130 W
• voltage: 220-240V, 50Hz
• amperage: 0.8A
• dimensions: 338 x 218 x 325 mm
• weight: 9.5 kg
• warranty: 1 year

Recommendations: The chiller should be cleaned every 3 - 4 months to remove any mineral deposits and limescale. Simply fill the chiller with clear vinegar, leave it for 24 hours and then rinse with water. Make sure you also place an air-circulation fan near the chiller to avoid heat build-up.

Please note:

1. The flow rate is determined according to the pump's maximum flow (submersible pump or another external power filter) and the circulation equipment.
2. Cooling performance is shown when the ambient temperature is 30°C, the water temperature before cooling is 28°C, the set temperature is 16°C and the chilled water is no more than 130 litres. As the water cooling decreases, the water temperature will drop.
3. Cooling efficiency is determined by the installation location, heat source, lighting, pump filter and other connecting parts. Special pumps and other accessories sold with Hailea series chillers must be used. Do not use alternatives to avoid affecting appliance performance.
4. When there is insufficient air exchange in a room, cooling efficiency is reduced if the ambient temperature rises due to heat from the unit.

This innovative reverse osmosis system is designed to provide clean and safe drinking water without the need for electrical power. With a filtration capacity of 190 liters per day, it is ideal for households seeking an efficient and economical water purification solution.

🔹 Main features:

• Filtration capacity: 190 liters per day
• No electrical power required: Does not require a pump or adapter
• Dimensions: 36 × 14,5 × 44 cm
• Filtration process:
  1. 25 cm PP Spun filter: Removes sand, rust, and other large particles
  2. 25 cm granular activated carbon (GAC): Removes chlorine, organic chemicals, and pesticides, improving the taste and odor of the water
  3. 25 cm carbon block (CTO): Provides deeper filtration, removing additional contaminants and improving water quality
  4. NSF-certified Hidrotek RO membrane: Removes dissolved impurities, heavy metals, bacteria, and viruses
  5. Post-carbon filter: Improves the taste of the water after purification
• Optional UV filter: A UV filter (reference number FUVW) can be added, using ultraviolet light to remove additional microorganisms such as bacteria and viruses, providing an even higher level of water safety and purity

🔹 Advantages:

• Chemical-free: Uses natural filtration without the need for chemicals
• Easy installation: The compact and modern design allows for easy installation in various spaces
• Low maintenance: The system is designed for long-term use with minimal maintenance requirements

GrowMax 10" x 2.5" De-Ionization Filter. Use with any reverse osmosis system to achieve water with 0.0EC (000 ppm).

4/7 mm Flexible hose – 50 metres

The flexible hose with a 4mm internal diameter and 7 mm external dimensions is intended for use in irrigation systems, especially drip and micro-sprinkler installations. Made of high-quality polyethylene (PE), this hose is resistant to UV rays and weather conditions, making it suitable for long-term outdoor use.​

Advantages:

• Flexibility: Easy to install and handle, even in complex garden layouts.​

• Durability: Withstands UV rays and weather conditions, preventing cracking and ageing.​

• Compatibility: Suitable for use with various fittings and drip-irrigation components.​

• Efficiency: Ensures even water distribution, helping achieve optimal plant irrigation.​

Technical specifications:

• Internal diameter: 4 mm​

• External diameter: 7 mm​

• Length: 50 metres​

• Material: Polyethylene (PE)​

• Colour: Black​

• Operating temperature: -10°C to +60°C​

Applications:

This hose is ideal for use in:​

• Drip irrigation systems​

• Micro-sprinkler systems​

• Gardening and greenhouses​

• Agricultural applications​

Automatic irrigation system for up to 10 pots at once — provides regular, even watering when you are away or do not have time to water by hand.

Detailed features

• Type: automatic drip/micro-irrigation system (drip irrigation / micro-drip system). 

• Suitable for: pots, terraces, balconies, greenhouses or small gardens — up to 10 individual plants (pots). 

• Material: plastic components (tubes, fittings), resistant to moisture and standard garden conditions. 

• Power supply / control: the system includes a control element (timer / valve) for automatic water delivery according to a set schedule. 

• Suitable water pressure and flow rate: a system for home gardens / pots — does not require professional plumbing.

• Use: automatic watering of pots/containers — can reduce the need for manual watering, especially when you are away.

Recommendations for use

• Connect the system to a water source — tap, faucet or hose — and place one tube in/next to each container or pot.

• Set a watering schedule (frequency and duration) according to the plants’ needs — more often for fresh greens and flowers, less often for resilient or deep-rooted plants.

• When planting out or repotting, ensure the soil is well moistened before watering and set the system for moderate delivery.

• If you are away, the system will maintain moisture automatically, but it is advisable to check the tubes and distribution periodically to prevent blockages.

• For maximum effectiveness, combine with well-drained pots and a suitable substrate to avoid overwatering.

iDrop PC pressure-compensating dripper 4 l/h (PC - pressure compensated)

• Constant dripper flow rate from 0,5 to 4,5 bar.

• Suitable for irrigation systems with long rows and uneven terrain with major elevation differences.

• Suitable for drip irrigation of orchards, vineyards, greenhouses and anywhere a precise flow rate is required

• Turbulent flow preventing deposits and clogging

• Made from next-generation polymers resistant to fertilisers and chemicals

• The base colour determines the dripper flow rate - the green colour corresponds to a flow rate of 4 litres per hour

• Operating pressure range 0,5 to 4,5 bar

Recommended minimum filtration grade - 120 mesh (130 microns)

To install, make a Ф2,0 - 2,5 - 3,0 mm hole with a punch in polyethylene pipe (see related products).

Installation on LDPE pipes is recommended.

Reverse-osmosis tubing is a key component of any reverse-osmosis system, facilitating the movement of water through the system and to your plants. It is an excellent solution for anyone needing reliable, durable tubing for their reverse-osmosis system.

AgroDrip 30 is a ready-made drip irrigation kit designed for up to 30 pots or plants. The system delivers water precisely and directly to the root zone, reducing water use and making daily plant care easier. The kit is suitable for balconies, terraces, greenhouses and small gardens, and can easily be connected to a water tap.

AgroDrip 30 is a practical solution for building a compact drip system without specialised tools. Thanks to the included microtubes, drippers and fittings, installation is quick and easy, while every plant receives the required amount of water directly in the root zone. This improves plant development and considerably reduces water loss through evaporation.

The kit is suitable for irrigating up to 30 pots and allows easy adaptation to the arrangement of your plants. When needed, the system can be combined with an irrigation controller for automatic watering, ensuring fully automated operation and reliable irrigation even when you are away.

Using drip irrigation maintains consistent substrate moisture, limits overwatering and creates optimal conditions for growing vegetables, herbs, ornamental plants and flowers outdoors as well as in greenhouses.

Technical specifications

✔️ Manufacturer: Agrodrip 

✔️ Model: Agrodrip 30

✔️ Type: Drip irrigation kit

✔️ Capacity: up to 30 pots or plants

✔️ Installation: To a water tap

✔️ Suitable for outdoor and indoor use

📦 The kit includes:

✔️ Pipe Ø16 mm – 15 m

✔️ Microtube Ø6 mm – 30 m

✔️ 20 pcs. Quick connector F16 x 3/4"

✔️ 100 pcs. Adjustable stake drippers

✔️ 20 pcs. Stake drippers

✔️ 20 pcs. Barbed tee Ø6 mm

✔️ 2 pcs. Barbed tee Ø16 mm

✔️ 2 pcs. Barbed elbow Ø6 mm

✔️ 2 pcs. Barbed elbow Ø16 mm

✔️ 1 pc. Barbed connector Ø7 mm x Ø6 mm

✔️ 1 pc. Awl Ø7 mm

✔️ 2 pcs. Barbed coupler Ø16 mm

✔️ 10 pcs. Barbed end cap Ø6 mm

✔️ 2 pcs. End clamp Ø16 mm

Application

Suitable for:

• Potted plants

• Balcony flowers

• Vegetables in pots

• Herbs

• Greenhouses

• Terraces

• Conservatories

• Yards

• Home and professional gardens.

📋 Instructions for use

1. Connect the kit to a water tap using the included adapters.
2. Position the main microtube according to the location of the pots.
3. Install the tees, elbows and drippers at each plant.
4. Check the system for leaks and correct water distribution.
5. If desired, connect the system to an automatic watering timer.
6. Periodically check the drippers and clean them when necessary.

⚠️ Important: For reliable operation and a longer system lifespan, it is recommended to use filtered water or install a filter before the system. This reduces the risk of dripper clogging and ensures even watering.

💡 Urban Botaniks tip: If you want fully automatic irrigation, combine AgroDrip 30 with an irrigation controller. This way, your plants will receive the required amount of water on set days and at set times, even when you are away from home.

Wilma 16

Hydroponic system Wilma 16 is a lightweight, easy-to-use and easy-to-carry hydroponic system. Pots of 6,5, 11 or 18 litres can be placed in each 4/8/10/16/20 tray. This gives plants sufficient space for optimal development. The Wilma growing systems are lightweight, easily portable and stable, allowing plants to remain upright even when fully grown. Wilma growing systems are specially designed for professional gardeners! For 16 plants, 1 sq/m. Suitable for use with mineral wool, expanded clay, coco or soil!

Dimensions: 115cm length x 115cm width x 20cm height 

Reservoir volume: 150 litres.

The AquaSolve UV steriliser, rated at 16 watts, operates at a wavelength of 254 nm (germicidal UV-C), providing up to 99.9% disinfection at a flow rate of up to approximately 7.6 litres per minute (≈2 gallons/min). It is suitable for drinking water production, irrigation systems and all situations where chemical-free sterility is required. 

Detailed features

• Lamp power: 16 W UV-C, low pressure (Low-Pressure Mercury Vapor).
• UV wavelength: 254 nm, effective against bacteria and microorganisms.
• Recommended flow rate for complete sterility: up to 7,6 L/min (≈2 GPM).
• Lamp life: approximately 9 000 hours of operation.
• Materials: the housing is made of high-quality material for maximum UV light transmission—typically stainless steel or a similar durable material. 
• Safety features: the UV steriliser does not add chemicals to the water and does not create secondary pollutants.

Recommendations for use

1. Filtration is recommended before the UV chamber—removal of solid particles (for example, with a 5 µm pre-filter or finer)—to improve UV radiation efficiency.
2. Replace the lamp every ~9 000 operating hours, even if it still lights up, because its effectiveness decreases over time.
3. Clean the quartz sleeve from the inside to remove calcium or mineral deposits that can block UV light.
4. Install the system so that the UV lamp has sufficient contact with the water—the inlet and outlet should be below or above the chamber, as specified in the instructions.
5. Make sure that no air or bubbles remain in the chamber—they reduce sterilisation efficiency.

Benefits

• Provides powerful disinfection without chemicals, at low energy cost.
• Capable of treating up to ~7,6 L/min—suitable for both small home and medium-sized systems.
• The lamp's ~9000-hour lifespan ensures long-term use before replacement is needed.
• Minimal maintenance—only periodic cleaning and lamp replacement.

16mm hose (FLEXI PIPE), 30m roll. is a high-quality flexible hose designed for a wide range of applications in gardening, hydroponic systems, irrigation and other industrial needs. Made from durable materials, this hose (tubing) offers excellent flexibility and long-lasting performance.

Key features:

• Diameter: 16 mm

• Roll length: 30 metres

• Material: Flexible UV-protected PVC

• Colour: Black

• Operating pressure: Up to 6 bar

• Temperature range: -10°C to +60°C​

Advantages:

• UV resistance: Protects against ageing and cracking when exposed to the sun.

• Flexibility: Easy to install and handle, even at low temperatures.

• Versatility: Suitable for use in various irrigation and hydroponic systems.

• Durability: Withstands mechanical stress and atmospheric influences.​

Applications:

• Drip irrigation systems

• Hydroponic installations

• Gardening and greenhouses

• Industrial applications requiring flexible connections

T.A RAINFOREST 6 INSERT 3INCH POT is an innovative hydroponic plant-growing system that allows you to create an ideal environment for the healthy, rapid growth of your plants. This high-quality product from T.A is designed to make the process of soilless plant growing easier and to ensure optimum delivery of nutrients and oxygen to the root system.

AgroDrip 15 is a ready-made drip irrigation kit designed for up to 15 pots or plants. The system delivers water precisely to the root zone, reducing water consumption and making daily plant care easier. The kit is suitable for balconies, terraces, greenhouses and small gardens, and can easily be connected to a water tap.

AgroDrip 15 is a practical solution for building a compact drip system without specialised tools. Thanks to the included microtubes, drippers and fittings, installation is quick and easy, and each plant receives the required amount of water directly in the root zone. This improves plant development and significantly reduces water loss through evaporation.

The kit is suitable for irrigating up to 15 pots and can be easily adapted to the arrangement of the plants. If necessary, the system can be combined with an automatic watering timer, providing fully automated operation and trouble-free irrigation even when you are away.

Using drip irrigation maintains consistent substrate moisture, limits overwatering and creates optimal conditions for growing vegetables, herbs, ornamental plants and flowers outdoors as well as in greenhouses.

Technical specifications

✔️ Manufacturer: Agrodrip 

✔️ Model: Agrodrip 15

✔️ Type: Drip irrigation kit

✔️ Capacity: up to 15 pots or plants

✔️ Installation: To a water tap

✔️ Suitable for outdoor and indoor use

📦 The kit includes:

✔️ Microtube Ø6 mm – 30 m

✔️ Microtube Ø7 mm – 1 m

✔️ 15 pcs. drippers with stake

✔️ 20 pcs. Ø6 mm barbed tees

✔️ 2 pcs. Ø6 mm barbed elbows

✔️ 1 pc. Ø7 × Ø6 mm barbed connector

✔️ 1 pc. male connector 1/2" × Ø7 mm

✔️ 1 pc. reducing coupling 3/4" × 1/2".

Application

Suitable for:

• Potted plants

• Balcony flowers

• Vegetables in pots

• Herbs

• Greenhouses

• Terraces

• Conservatories

• Yards

• Home and professional gardens.

📋 Instructions for use

1. Connect the kit to a water tap using the included adapters.
2. Position the main microtube according to the location of the pots.
3. Install the tees, elbows and drippers at each plant.
4. Check the system for leaks and correct water distribution.
5. If desired, connect the system to an automatic watering timer.
6. Periodically check the drippers and clean them when necessary.

⚠️ Important: For reliable operation and a longer system lifespan, it is recommended to use filtered water or install a filter before the system. This reduces the risk of dripper clogging and ensures even watering.

💡 Urban Botaniks tip: If you want fully automatic irrigation, combine AgroDrip 15 with a watering timer. This way, plants will receive the required amount of water on precisely scheduled days and times, even when you are away from home.

Automatic irrigation timer for 1 zone, which controls the water supply according to a set schedule — convenient for gardens, greenhouses, flower beds and hose irrigation systems.

• Type: 1-zone electronic timer.
• Power supply: batteries (2xAA)
• Material: ABS+PP housing, resistant to outdoor conditions.
• Operating pressure: approximately 0.5–8 bar, suitable for standard plumbing/hose systems.
• Watering settings: option to set frequency — from hourly to daily, and repetitions from 1 day to 7 days.
• Functions: automatic watering, waterproof housing, convenient for home gardens and greenhouses.

Recommendations for use

• Connect the timer to a standard hose or irrigation system, set the desired watering time and frequency — the device will take care of it automatically.
• Suitable for gardens, balconies, greenhouses, pots, flower beds — where you cannot water manually every day.
• A good choice when no one is present (holiday, travel, etc.) to maintain regular moisture.
• Use only at water pressure between 0.5 and 8 bar

Vontron 75 GPD reverse osmosis membrane. Capacity 280 L/24 hours. Compatible with standard household reverse osmosis systems. Used as the fourth water-filtration stage in household reverse osmosis systems.

Technical specifications:

Operating pressure 2.8-6 atm

Operating temperature from +2 to +45^oC

Capacity 280 L/24 hours

Pore size 0,001 µm

Osmotic membrane module size 30 cm x 4.5 cm

Purification efficiency 95%

Inlet water pH range 2-11

Inlet water range – short-term resistance (30 min.) – 1-12

Chlorine resistance up to 0.1 ppm

Maximum water hardness: 400 mg CaCO3

Maximum salinity 2000 ppm

Maximum turbidity 1 NTU

Maximum iron and manganese content: < 0,05 ppm

Active membrane surface area 0.38 m2

Water Master electric sprayer with a 2-litre capacity, designed for precise and convenient application in the garden, hydroponics or at home. Lightweight, ergonomic design with an adjustable nozzle for a fine mist or a powerful jet stream. Powered by a 2000mAh lithium battery that charges quickly via USB-C. Made from recyclable materials for a longer lifespan. 

Detailed features

• Capacity: 2 litres
• Material: recyclable ABS, PP and HDPE
• Battery: lithium, 2000mAh, 3.7V
• Charging: USB Type-C cable (included)
• Dimensions: ø13 × 28.7 cm
• Weight: ~550 g
• Nozzle: adjustable for mist or jet
• Design: lightweight, ergonomic, easy to use even in hard-to-reach areas

Recommendations for use

• Charge fully before use with the supplied USB-C cable.
• Use the mist function for precise watering, or the jet when concentrated application is required.
• Thanks to the recyclable material and built-in battery, the product is more environmentally friendly.
• Suitable for watering, fertilising and pest-control spraying.

Summary – Benefits

• Convenient capacity: 2 litres — ideal for quick tasks.
• Battery with USB-C charging: a convenient, battery-powered solution without the need for additional batteries.
• Flexible spraying: adjustable between mist and jet.
• Compact and durable: lightweight and ergonomic, made from durable materials.
• Eco-friendly choice: recyclable housing, less waste.

Quiet and powerful Hailea ACO-9820 air pump, delivering up to 60 L/min (3 600 L/h) through 10 outlets, with a sound-insulated design and waterproof housing.

Detailed features

• Maximum flow rate: 60 L/min (3 600 L/h)
• Power consumption: 35 W
• Noise level: < 40 dB
• Max. pressure: > 0,03 MPa
• Outlets: 10 ports, via a plastic manifold
• Dimensions (L × W × H): 243 × 186 × 201 mm
• Weight: 5,60 kg
• Voltage / power supply: 220-240 V (e.g. European version

Special design features:

  • Dual vibration absorption and sound insulation system for quiet operation.
  • Fully waterproof construction — no additional measures are needed.
  • The included manifold provides multi-channel distribution.

Benefits

Hailea ACO-9820 combines high flow, quiet operation and versatility — with 10 outlets, a sound-insulated design and waterproof housing. It is suitable for systems with a high aeration demand, such as reservoirs, ponds or hydroponic installations.

16mm hose (FLEXI PIPE) for 1m. is a high-quality flexible hose intended for a wide range of applications in gardening, hydroponic systems, irrigation and other industrial needs. Made from durable materials, this hose offers excellent flexibility and longevity.

Key features:

• Diameter: 16 mm

• Minimum quantity: 1 metre

• Material: Flexible UV-protected PVC

• Colour: Black

• Operating pressure: Up to 6 bar

• Temperature range: -10°C to +60°C​

Advantages:

• UV resistance: Protects against ageing and cracking when exposed to the sun.

• Flexibility: Easy to install and handle, even at low temperatures.

• Versatility: Suitable for use in various irrigation and hydroponic systems.

• Durability: Withstands mechanical stress and atmospheric influences.​

Applications:

• Drip irrigation systems

• Hydroponic installations

• Gardening and greenhouses

• Industrial applications requiring flexible connections

Cylindrical air diffuser (air stone) in grey, designed for underwater placement to create fine air bubbles and optimal aeration.

Detailed specifications:

• Material: mineral / plastic composition — typical for CAPASTEC air stones
• Dimensions: 150 mm (≈ 5,9″).
• Shape: cylindrical with square ends — a design allowing easy connection and installation
• Colour: grey / dark (grey / black).
• Suitable for: aquariums, ponds, aeration systems — for both fresh and salt water.
• Requirement before first use: immerse / soak in water for a specified period (for example, 1 hour) for proper operation.
• Maintenance: if clogged — wash or soak to restore porosity.
• Connection: standard hose / tubing compatible with a diameter of around 4 mm (for this type of product).

Recommendations for use:

• Before use, soak the diffuser for at least 30–60 minutes so that it becomes saturated and starts working evenly.
• Connect the diffuser to a compressor / pump using a suitable hose and check that the pressure is appropriate — if it is too high, the bubbles may become large and rise quickly without effect (a problem observed with air diffusers).
• Place the diffuser in the lowest part of the reservoir/pond for better bubble distribution.
• Clean the stone regularly when algae or sediment build up, using a soft brush or a mildly acidic solution, then rinse thoroughly.
• Avoid high pressure and operation with a weak compressor — this may damage the diffuser's porous structure.

Benefits

This grey cylindrical 150 mm diffuser provides efficient, uniform airflow through numerous fine bubbles, improving oxygen enrichment in reservoirs and ponds. It is easy to install and maintain, and is compatible with various systems thanks to its universal design and durable material.

🔹 6 mm irrigation hose (25 m roll) is a flexible PVC hose designed for drip irrigation in small and medium-sized gardens, greenhouses, and balconies. With its compact size and easy installation, it is ideal for precise and economical watering of plants.

🔹 Detailed specifications:

• Material: Flexible PVC
• Diameter: 6 mm
• Length: 25 meters
• Color: Black
• Durability: Suitable for outdoor use, but not UV-resistant
• Application: Drip irrigation in small and medium-sized gardens, greenhouses, and balconies
• Compatibility: With standard 6 mm fittings and drip emitters

🔹 Recommendations and method of use:

1. Unroll the hose on a flat surface and leave it to relax for easy installation.
2. Connect one end of the hose to the main water supply pipe using a suitable fitting.
3. Place drip emitters or branch connectors at intervals of 30 cm to ensure even irrigation.
4. Position the hose around the plants, securing it with clamps or clips.
5. Adjust the water flow according to the plants' needs and growing conditions.

✅ Benefits of use:

• Precise irrigation: Provides the exact amount of water directly to the root system of the plants.
• Water savings: Reduces water waste and prevents evaporation.
• Easy installation: Quick and convenient installation without the need for specialized tools.

Flexibility: Suitable for various types of plants and growing conditions.

Repair Piece for Sump is a solution for repairing damaged sump tray wells. It is made in dimensions of 175 × 55 mm and allows easy replacement of defective sections—without the need to replace the entire tray.

Detailed features

• Dimensions: 175 × 55 mm — suitable for restoring damaged areas in sump trays.
• Installation: Clean and dry the surface of the damaged section. Apply the branded Staal & Plast adhesive, position the Repair Piece and, if necessary, seal the edges to ensure a strong and waterproof bond.
• Additional work: After fixing, it may be necessary to drill new holes for valves if the original ones fall within the new area.

Recommendations for use

• Prepare the surfaces thoroughly—they must be clean and dry before bonding.
• Use the original Staal & Plast adhesive to ensure durable and resilient bonding.
• After installation, if necessary, seal the edges with sealant to prevent the ingress of dirt and moisture.
• If sump valves need to be installed, you can drill new holes in the repaired section.

Benefits

The repair piece for sump trays provides an economical and reliable repair for damaged sections, without the need to replace the entire tray. Its 175×55 mm size allows precise replacement. Natural bonding and sealing guarantee tightness and long-term functionality, including the option of fitting new valves.