Everything for Seedlings

CLONEX Rooting Gel 50ml. is a rooting gel used by hobbyists and professional gardeners around the world for the most successful rooting.

• Easy to use.
• Adheres instantly to the cut tissue, sealing it and eliminating the risk of infection or embolism.
• Contains rooting hormone 3000 particles per million, the full strength needed for explosive root development.
• Gel – far safer than liquids or powders because it cannot spill or blow away. Unlike liquids and powders, Clonex rooting gel will remain completely in contact with the stem throughout the rooting period.
• It does not wash off when you water your plants.
• Works with its partner products Root Riot and Clonex Mist to give young plants the healthiest and strongest start to their development.

Instructions for use:

• Choose young branches / shoots from the healthiest plants. If possible, the plant tips may be sprayed with Clonex Mist once or twice a week before taking cuttings. Cut the shoot tips, each with four or five pairs of leaves, and remove the lower two pairs of leaves.
• Always use a clean, sharp knife or blade. Make a precise diagonal cut at the base of the shoot, directly below the lowest leaf junction.
• Pour a small amount of Clonex rooting gel into a separate container for immediate use. Do not dip the cut tissue into the original container and do not return unused Clonex rooting gel, as this may contaminate the remaining gel.
• Immediately dip the cutting approximately 15 mm into Clonex rooting gel, then place the cutting in the rooting medium (rockwool, Jiffy, etc.) deeply enough for it to be held securely.
• Spray the new cuttings with Clonex Mist and place them in a propagator. The lid and vents should be closed.
• After 2-3 days, spray the cuttings again with Clonex Mist and open the propagator vents slightly.

Check for new roots after a few days—continue spraying with Clonex Mist until the plant is ready for transplanting. If planting in soil, carefully place the soil around the roots to avoid damaging them.

TIP: New cuttings should be kept in a closed propagator, with most plant species thriving at a temperature of 21-24°C and relative humidity of around 90%. Once new roots appear, your plant will need to be hardened off. Open the propagator slightly to allow a small amount of air in. Open it a little more each day until you eventually remove the lid completely. When the young plants are well developed, they can be placed in larger rockwool cubes or transplanted into soil or coco. Carefully place the soil around the new roots to avoid damaging them.

ROOT!T Rooting Gel 150ml is a rooting gel suitable for use with ornamental plants, softwood and hardwood plants, and leaf and root cuttings. This gel adheres tightly to the cutting stem and, with the practical bottle tip, can be applied directly into the rooting substrate (rockwool plugs, peat plugs, coconut fibre, compost or soil). For best results, we recommend using it together with ROOT!T Natural Rooting Sponges, 50 rooting sponges.

• Roots in 3-4 days without stress or wilting, while a strong root system develops from day one!
• Convenient packaging with a cap, so you do not need to decant it into other containers.
• Contains no hormones!
• Contains vitamin B1, which helps the root system grow faster.
• "Seals" the cutting by forming a protective layer over the cut surface, thereby preventing infections and dehydration.

Instructions for use:

• Always use sterile tools when taking cuttings!
• Pour approximately 1ml of gel directly into the hole for the cutting, so the gel will not be "wiped off" when inserting the cutting!
• Make sure the cuttings are placed immediately into the gel and rooting medium to prevent wilting and maintain the flow of auxins (growth hormones) moving down the stem to initiate root growth. rooting gel for cuttings!

Compressed peat pellet Jiffy-7 41 mm in a pack of 100, which expands when moistened and serves as a self-expanding substrate for seeds and cuttings.

Detailed features

• Delivery format: compressed disc (diameter when dry)
• Size after saturation: diameter ~ 41 mm
• Materials: peat (sphagnum peat), wrapped in biodegradable netting (to EN13432 standard)
• pH value: around 5.3 (when using the peat variant)
• Electrical conductivity (EC): ~ 1.1 (± 0.3) for standard Jiffy-7
• The price is for 100 pellets. Available loose in packs of 100 pieces, or cartons of 1000 pieces.
• Porosity / air capacity: high, to stimulate root growth
• Expansion: after moistening, the pellet expands several times (up to 5–7 times
• Sustainability and certification: biodegradability to the EN13432 standard, products with ISO certifications

Recommendations for use

• Place the dry pellet in a suitable container and pour in warm, clean water, allowing it to expand.
• Once it has expanded, drain off the excess water so that the substrate is not overly wet.
• Sow the seeds or insert the cuttings directly into the pellet.
• Maintain moderate moisture, but avoid overwatering — slight drying is better than retaining water.
• Once the plants have developed sufficiently, the pellet can be planted directly into soil or a larger container — there is no need to separate it, which minimises root damage.
• After use, the netting decomposes according to a biodegradability standard, making the product environmentally friendly.

Benefits

The Jiffy-7 41 mm pellet combines substrate and container in one; when moistened, it becomes an ideal environment for plant germination and rooting. Its high porosity and suitable chemical characteristics support root development, while the ecological net wrap allows direct planting without plant stress.

Compressed peat pellet Jiffy-7 41 mm, which expands when moistened and acts as a self-expanding substrate for seeds and cuttings.

Detailed features

• Delivery format: compressed disc (diameter when dry)
• Size after saturation: diameter ~ 41 mm
• Materials: peat (sphagnum peat), wrapped in biodegradable netting (to EN13432 standard)
• pH value: around 5.3 (when using the peat variant)
• Electrical conductivity (EC): ~ 1.1 (± 0.3) for standard Jiffy-7
• The price is for 1 pellet, available loose, in packs of 100 units or boxes of 1000 units. 
• Porosity / air capacity: high, to stimulate root growth
• Expansion: after moistening, the pellet expands several times (up to 5–7 times
• Sustainability and certification: biodegradability to the EN13432 standard, products with ISO certifications

Recommendations for use

• Place the dry pellet in a suitable container and pour in warm, clean water, allowing it to expand.
• Once it has expanded, drain off the excess water so that the substrate is not overly wet.
• Sow the seeds or insert the cuttings directly into the pellet.
• Maintain moderate moisture, but avoid overwatering — slight drying is better than retaining water.
• Once the plants have developed sufficiently, the pellet can be planted directly into soil or a larger container — there is no need to separate it, which minimises root damage.
• After use, the netting decomposes according to a biodegradability standard, making the product environmentally friendly.

Benefits

The Jiffy-7 41 mm pellet combines substrate and container in one; when moistened, it becomes an ideal environment for plant germination and rooting. Its high porosity and suitable chemical characteristics support root development, while the ecological net wrap allows direct planting without plant stress.

Grodan rockwool cube 4cm, 1 pc. for rooting and hydroponics.

• dimensions: 4x4x4cm.

ROOT!T Large Value Propagator is a box for seed germination or rooting cuttings. It consists of:

• lid with two humidity-control vents
• tray with longitudinal channels to prevent overwatering
• dimensions L/W/H: 57 x 37 x 21cm.

Compressed peat pellet Jiffy-7 33 mm, which expands when moistened and serves as a self-expanding substrate for seeds and cuttings. Pack of 100 pieces

Detailed features

• Delivery format: compressed disc (diameter when dry)
• Size after saturation: diameter ~ 33 mm
• Materials: peat (sphagnum peat), wrapped in biodegradable netting (to EN13432 standard)
• pH value: around 5.3 (when using the peat variant)
• Electrical conductivity (EC): ~ 1.1 (± 0.3) for standard Jiffy-7
• The price is for a pack of 100 peat pellets. They are also available loose, in packs of 100 pieces and in cartons of 2000 pieces.
• Porosity / air capacity: high, to stimulate root growth
• Expansion: after moistening, the pellet expands several times (up to 5–7 times
• Sustainability and certification: biodegradability to the EN13432 standard, products with ISO certifications

Recommendations for use

• Place the dry pellet in a suitable container and pour in warm, clean water, allowing it to expand.
• Once it has expanded, drain off the excess water so that the substrate is not overly wet.
• Sow the seeds or insert the cuttings directly into the pellet.
• Maintain moderate moisture, but avoid overwatering — slight drying is better than retaining water.
• Once the plants have developed sufficiently, the pellet can be planted directly into soil or a larger container — there is no need to separate it, which minimises root damage.
• After use, the netting decomposes according to a biodegradability standard, making the product environmentally friendly.

Benefits

The Jiffy-7 33 mm pellet combines substrate and container in one; when moistened, it becomes an ideal medium for germination and rooting. Its high porosity and suitable chemical properties support root development, while the eco-friendly net covering allows direct planting without stress to plants.

Eazy Plug CT150 tray with 150 pcs. of dry propagation plugs/blocks made from a specially formulated substrate with added nutrients. It provides good water (nutrient solution) and air conductivity, which is very important for developing a good root system from the start.

• for seed germination or for rooting cuttings / clones
• for fast and vigorous rooting
• always the perfect water/air ratio (20/80%)
• 100% biodegradable

It’s that simple: just water them generously and let the excess water drain away! Eazy Plug automatically regulates optimal moisture.

Features:

• Plug dimensions: 2.5 x 2.5 x 3.0 cm
• tray dimensions: 52.5 x 31.0 x 3.0 cm
• EC: 1 mS/cm
• pH: 5.9

Benefits of Eazy Plug:

• self-regulating
• easy to use
• air pruning for a significant increase in root mass
• suitable for gradually drier growing conditions

Compatibility:

• Eazy Plug is compatible with all known growing media, such as rockwool, coco substrate, black and white peat, garden soil, potting soil, soilless growing, fine bark and wood mulch, wood fibre, perlite, pumice, sand, clay and vermiculite.

Applications:

• Eazy Plug can be used in ebb-and-flow hydroponic irrigation systems (Ebb & Flow), drip irrigation, NFT*, wick systems, floating rafts, DWC*, aquaponic systems and soil cultivation (indoors and outdoors).

Agrolite 4.30 LED is an innovative lighting product with four adjustable panels of 30W each, reaching a total output of 120W. The lamp's geometry, high efficiency and low heat output make it the ideal lighting fixture for the germination, growth and flowering stages.

• intended use: for growth and flowering
• power: 120W
• efficiency: 2.2 µmol/J
• service life: 20 000 hours
• socket: E27

Note: the lamp is sold without a lamp holder!

A lamp holder can be purchased here!

Warning: do not use with dimmers!

Technical specifications:

ROOT!T VALUE Rooting Sponge Propagation Kit is a complete kit for germinating seeds or rooting cuttings. The kit contains:

• propagator with a humidity-control vent
• tray with 24 cells
• 24 pcs. rooting sponges
• 15 ml sample initial feed
• 15 ml sample rooting gel
• English-language instructions for optimal results
• dimensions L/W/H: 38 x 24 x 18.5 cm.

Eazy Plug CT77 tray, 77 pcs dry rooting and seedling plugs made from a specially developed substrate with added nutrients, providing good water (nutrient solution) and air conductivity, which is crucial for developing a strong root system from the start.

• for seed germination or for rooting cuttings / clones
• for fast and vigorous rooting
• always the perfect water/air ratio (20/80%)
• 100% biodegradable

It’s that simple: just water them generously and let the excess water drain away! Eazy Plug automatically regulates optimal moisture.

Features:

• Plug dimensions: 3.5 x 3.5 x 3.0 cm
• tray dimensions: 52.5 x 31.0 x 3.0 cm
• EC: 1 mS/cm
• pH: 5.9

Benefits of Eazy Plug:

• self-regulating
• easy to use
• air pruning for a significant increase in root mass
• suitable for progressively drier growing

Compatibility:

• Eazy Plug is compatible with all known growing media, such as rockwool, coco substrate, black and white peat, garden soil, potting soil, soilless growing, fine bark and wood mulch, wood fibre, perlite, pumice, sand, clay and vermiculite.

Applications:

• Eazy Plug can be used in ebb-and-flow hydroponic irrigation systems (Ebb & Flow), drip irrigation, NFT*, wick systems, floating rafts, DWC*, aquaponic systems and soil cultivation (indoors and outdoors).

Moistening time:

• when top-watered < 10 seconds
• when immersed < 10 seconds
• drip irrigation – depends on the preset amount
• when bottom-watered < 45 seconds

ROOT!T Propagator Tray Insert is a 60-cell tray for rooting plugs, suitable for placing in a ROOT!T propagator.

• 60 cells
• dimensions: 52x32x5cm

UGRO Benefit Rhiza1200 4 g is a fast-acting, non-pathogenic rooting powder that starts working within 24 hours, accelerating plant growth and improving the accumulation of valuable molecules in your plant. The active natural ingredient, Glomus intraradices, significantly increases the biomass of roots and shoots (cuttings / young branches).

• contains Glomus intraradices
• accelerates plant growth
• improves the accumulation of valuable molecules in plants
• increases biomass of roots and shoots

Application:

• Add 1 g to 5 L of water or 1 g to the substrate of each plant when transplanting.

tray for JIFFY
84 cells

Tray specially designed for Jiffy-7C 33mm blocks.

Dimensions 52x32cm.

Jiffy-7 trays are designed to hold the pellets securely while allowing free air circulation, which helps prevent disease and supports root development.

ROOT!T Cutting Mist 100 ml is a cutting spray that prevents losses during the critical first days, when cuttings are most vulnerable. Ideal for softwood and semi-hardwood plants. With this spray, you can treat the mother plant (from which you will take cuttings) 2-3 days in advance, as well as the cuttings themselves during the first three days after they are taken.

• improves rooting
• revitalises stressed, drooping cuttings and brings them back to life
• contains essential vitamin and mineral blends
• prevents dehydration of cuttings
• you can use it with ROOT!T Rooting Gel 150 ml rooting gel, or on its own

Directions for use:

• Spray the mother plant from which you will take cuttings 2-3 days in advance.
• Spray the cuttings during the first 3 days after taking them.

tray for JIFFY
60 cells

Tray specially designed for Jiffy-7C 41mm pellets.

Dimensions 52x32cm.

Jiffy-7 trays are designed to hold the pellets securely while allowing free air circulation, which helps prevent disease and supports root development.

Clonex Pro Start 300ml is a high-quality plant fertiliser, consisting of a blend of mineral nutrients and organic extracts. It supports exceptional root development and early growth in cuttings, seedlings and young plants.

• for successful seed germination every time
• for soaking the growing medium of your cuttings
• for initial feeding of your young plants

Mineral nutrients:

1. Optimal levels of Boron and Calcium for early root development.
2. A precise Potassium:Nitrogen ratio for the early development of leaves.
3. Balanced levels of chelated micronutrients for use with low EC levels (electrical conductivity).
4. Phosphorus for energy conversion and improved metabolism.

Organic extracts:

1. A blend of different seaweed species for an optimal balance of bioactive compounds to support healthy root formation, followed by leaf growth.
2. Targeted L-amino acids to stimulate metabolism and stress resistance.
3. Humic and fulvic extracts for improved nutrient uptake.

Why you can rely on Clonex Pro Start:

1. Always low in heavy metals and chlorides.
2. Guaranteed pH stability of the nutrient solution.
3. Fully water-soluble.

ROOTiT Propagator Tray is a tray / base for the ROOT!T propagator.

• equipped with longitudinal channels to prevent overwatering
• dimensions: 57x37x5.5 cm.

ROOT!T Thermostat for Heat Mat is an electronic device that gives you full control over the temperature in the root zone during germination / rooting. By switching heat mats on and off, the device maintains the precisely set desired temperature (10-30ºC). It is compatible with all ROOT!T heat mats.

• Maintain optimal temperatures for your plants!
• Easy to plug in!
• Easy to use and control!
• Sensor cable length: 1.8 m
• Max. load: 1000 W / 4.3 A

Preparing for use:

1. Place the temperature sensor in the propagator or in the area to be heated. It can be suspended using the rubber suction cup or placed in the substrate (image 3).
2. Place the thermostat outside the propagator or growing area – the thermostat and output socket must always be kept in a dry place! DO NOT IMMERSE IN WATER OR LIQUIDS!
3. Plug the heat mat or other heating device into the output socket.
4. Connect the thermostat to the mains supply – the POWER indicator should light up.
5. Proceed to set the desired temperature to be maintained.

Setting the thermostat:

The display shows the current temperature at the sensor. Press UP to display degrees Fahrenheit ºF or DOWN to display degrees Celsius ºC – the corresponding indicator will light up.

1. Press the SET button to show the desired temperature on the display; after 3 seconds, it will return to the current temperature.
2. Press and hold the SET button for 3 seconds; the display will start flashing. Press UP or DOWN to select the desired temperature to be maintained.
3. Press SET again to return the display to the current temperature; if left untouched, it will return to the current temperature display after 30 seconds.

The HEATING indicator will light up if the current temperature is lower than the desired temperature – the heat mat / heating device is now ON. The HEATING indicator will not light up if the current temperature is higher than the desired temperature – the heat mat / heating device is now OFF.

🔹 Solux i-Clone 2x20W LED Tube is high-quality lighting designed to optimally illuminate rooting cuttings and support mother plants. With its full-spectrum lighting and the ability to connect up to 10 tubes in series, this product offers flexibility and efficiency for any indoor garden.

🔹 Detailed specifications:

• Manufacturer: Solux
• Model: i-Clone 2x20W LED Tube
• Lighting type: LED tube with two 20W LEDs
• Color temperature: 6500K (suitable for vegetative growth and flowering)
• Light efficiency: 2.4 μmol/s per watt
• Product lifespan: 55,000 hours
• Dimensions: 120 cm in length
• Weight: 330 g
• IP rating: IP65 (resistant to dust and moisture)
• Connection: Can connect up to 10 tubes in series via IP65 input/output
• Package contents: 2 LED tubes, power cable, mounting brackets

🔹 Recommendations and instructions for use:

1. Choose a suitable place to install the tubes, ensuring good light distribution.
2. Use the provided mounting brackets to attach the tubes to a wall or ceiling.
3. Connect the tubes in sequence using the IP65 input/output connectors to connect up to 10 tubes in series.
4. Connect the power cable to the first tube and plug it into the electrical mains.
5. Adjust the lighting according to the plants' needs, ensuring a suitable photoperiod and light intensity.

✅ Benefits of use:

• Improved rooting: Stimulates fast and healthy rooting of cuttings.
• Support for mother plants: Provides optimal conditions for keeping mother plants healthy.
• Flexibility: The ability to connect up to 10 tubes in series allows easy expansion of the lighting system.
• Energy efficiency: Low energy consumption and a long product lifespan.
• Durability: IP65 protection against dust and moisture, suitable for various indoor conditions.

Ferro RADIX 60 ml. is a unique cloning agent, specially developed for use when taking cuttings. With it, you treat young cuttings only once!

• developed on the basis of natural, organic substances
• stimulates explosive root growth and the development of a powerful root system

Directions for use: Shake the bottle well before use! Dip the cutting into RADIX, to a depth of 2-3 cm, only once! Then you can place the cutting in previously prepared rockwool cubes or peat pellets for seedlings. If the solution is too strong for your plants, you can dilute it with demineralised or rainwater.

Additional product information can be obtained from the manufacturer's website: here!

PLAGRON SeedBooster Plus 10ml is a powerful, safe fertiliser for the first stage of plant growth. It provides young plants with all essential nutrients, significantly accelerating the growth process.

• Make seed germination even more successful!
• Significantly accelerates the growth of young plants.
• Supplies the plant with all essential nutrients.
• NPK: 5-4-7

Directions for use:

• Shake well before use!
• Dissolve 7 drops of Seedbooster Plus in 1l of water at a recommended temperature of 23ºC. Then place your plant's seeds to soak in this solution for 12 hours. 
• Apply Seedbooster Plus for up to one week after rooting to protect your young plants.

Grodan mineral wool cubes - tray of 77 pcs. for rooting.

• tray size: 53x32 cm.
• cube dimensions: 3.5x3.5x4 cm.\n

Cultilene rockwool cubes - tray of 77 pcs. for rooting.

• tray size: 53x32 cm.
• cube dimensions: 3.5x3.5x4 cm.\n

Clonex MIST 300ml is the latest innovation in cloning technology, designed to make cloning even more successful. An innovative, sophisticated combination of amino acids and mineral nutrients to accelerate the healthy rooting process. Clonex Mist is a ready-to-use product that delivers:

• rapid root formation
• healthy plants
• consistent results every time

Instructions for use:

• Choose a healthy plant with good, healthy shoot tips. If possible, spray the plant tips with Clonex Mist once or twice a week before taking cuttings. 
• Use a sharp, clean blade, such as a scalpel, to make a diagonal cut at the base of the stem, just below the lowest leaf node.
• If you have Clonex rooting gel, promptly dip the cutting into the gel.
• Then immediately place the cutting in the growing medium, such as rockwool or Jiffy, which you have pre-moistened.
• Spray the new cuttings with Clonex Mist and place them in a propagator. Keep the lid and vents closed.
• After 2-3 days, spray the shoots again with Clonex Mist and open the propagator vents slightly.

Check the new roots after a few days - continue spraying with Clonex Mist until the plant is ready to be transplanted. If planting in soil, carefully place the soil around the roots to avoid damaging them.

TIP: Repeat spraying every 2-3 days or if your cuttings look dry. Open the propagator vents a little more each day. Light condensation inside the propagator indicates suitable relative humidity.

Glass House Propagator 64 is a propagator made of high-quality rigid plastic, suitable for seed germination, growing small plants or rooting cuttings.

• dimensions: 59x39x24cm.
• a sturdy, durable and waterproof polypropylene tray
• a transparent, impact-resistant polystyrene lid for maximum light transmission
• sliding ventilation openings for easy humidity control

ROOT!T Medium Heat Mat is a heat mat that evenly warms the root zone, improving germination and rooting. Maintaining a consistent temperature is a key factor for success in the early stages, when young plants are at their most delicate and vulnerable.

• dimensions W/L: 40x60cm.
• Accelerates seed germination or clone rooting by days.
• Warms the root zone 5.5-11˚C above ambient temperature.
• Fully waterproof, scratch-resistant and durable.
• To set your desired precise temperature, use together with the ROOT!T heat mat thermostat.

Instructions for use:

1. Place the heat mat on a thoroughly dry surface.
2. For better results, place the mat on an insulated surface rather than directly on a cold floor.
3. Place the propagation tray (seeds, clones) on the mat. Cover it with a propagator lid – this will keep the root zone warm and maintain humidity for better rooting.
4. Connect to the mains power supply (220-240V).
5. This heat mat is designed to warm the root zone 5.5-11˚C above ambient temperature.

Warning:

• Fire or electric shock may result from improper use!
• Ensure that there are no sharp objects on the surface beneath the heat mat that could puncture it! Do not place the mat directly in the tray / propagator and do not cover it with soil or another growing medium!
• Do not cover the mat with thermal insulation materials, as this may cause overheating!
• Do not immerse in water!

The Neptune Hydroponics heated propagator is a quality propagator with a 12V heating mat. It lets you germinate flowers, vegetables or aromatic herbs during the winter months; their seeds will develop at an ideal temperature and be ready for transplanting at the beginning of spring.

• dimensions: 38 x 25 x 19 cm.

Secret Jardin Cosmorrow Power 1x20W is a power supply for one 20W LED strip from the Cosmorrow series.

• power: 20W
• voltage: 100-220V
• frequency: 50/60 Hz
• weight: 0.35kg
• protection rating: IP54